What breaks an STL file
An STL is nothing but a list of triangles. It has no idea which triangles are neighbours, so nothing stops an export from leaving a gap, writing a face twice or pointing one the wrong way. The slicer then has to guess where the inside of the part is, and when it guesses wrong you get missing layers, filled-in holes or a part that will not slice at all.
| Problem | What you see when slicing | Repaired here |
|---|---|---|
| Holes (open edges) | Missing walls, layers that vanish, "not manifold" warnings | Yes |
| Flipped triangles | Random gaps or solid patches where the part should be hollow | Yes |
| Inside-out body | The part slices as empty space | Yes |
| Duplicate triangles | Stray internal walls, "non-manifold edges" | Yes |
| Zero-area triangles | Warnings, sometimes slow slicing | Yes |
| Seams that do not quite meet | Hairline gaps along curved surfaces | Yes |
| Edges shared by three or more faces | "Non-manifold" warnings where parts touch | Reported |
| Parts passing through each other | Usually prints fine, sometimes odd infill | No |
How the repair works
First, vertices that sit within a thousandth of a millimetre of each other are joined, which is what turns a loose list of triangles into a connected surface. Triangles that collapse to a line and exact duplicates are dropped.
Next, every edge is checked. In a sound mesh each edge belongs to exactly two triangles and they run along it in opposite directions. Where two neighbours disagree, the minority is turned, so a model that is mostly right keeps its orientation. A body whose volume comes out negative is inside out and is turned as a whole, unless it sits inside another body, in which case it is a cavity and is meant to face inward.
Then the holes. The open edges are followed around each gap until they form a closed outline, and the outline is filled with new triangles. Flat and gently curved holes close cleanly. A hole across a strongly curved surface is closed with a flat patch, so check that area in the preview.
Finally the whole mesh is checked again from scratch, and that second check is what the "After" column shows. If something could not be repaired, the page says so instead of calling the file fixed.
If problems remain
Raise the join distance if open edges are left along a seam. Tick "Remove loose fragments" if the export left specks floating near the part. If the report shows edges shared by three or more faces, two bodies are touching along a line or a face: go back to the CAD model and either merge them into one solid or move them apart.
You can look at the result from every side in the STL viewer, change the format with the 3D file converter, or see how long it will take with the print time estimator.
Frequently asked questions
How do I repair an STL file?
Drop the file onto this page. It is checked edge by edge, the problems that can be repaired safely are fixed, and a before and after table shows what changed. Then download the repaired STL. There is nothing to install and no account.
What does "watertight" or "manifold" mean?
A printable model is a closed skin with a clear inside and outside. In mesh terms, every edge is shared by exactly two triangles, the two triangles agree on which side is out, and the enclosed volume is positive. A slicer needs that to decide where to put plastic. A hole, a triangle facing inward or a stray duplicate breaks it.
Which problems does this fix?
Holes, triangles facing the wrong way, whole bodies that are inside out, duplicate triangles, zero-area triangles and seams where neighbouring triangles do not quite share a vertex. It can also remove tiny loose fragments if you tick that option.
Which problems does it not fix?
Two things. Parts that pass through each other are not detected, because each part can be perfectly closed on its own. And edges shared by three or more faces are counted and reported but left alone, because the right fix depends on what the designer meant. Both usually need changing in the CAD model, and most slicers print them anyway.
Is my file uploaded?
No. The file is read and repaired by your own browser, in a background worker on your device. It is not sent to a server, so it also works for files you are not allowed to share.
Will repairing change the shape or size of my model?
Not the parts that were already there. Existing vertices stay where they are apart from being joined when they sit closer than the join distance, 0.001 mm by default. New triangles are only added to close holes, and the table shows the volume before and after so you can see the effect.
My slicer says the model has errors but this says it is watertight. Why?
Slicers also warn about overlapping parts, walls thinner than the nozzle and very small features. Those are not mesh errors, so a watertight file can still trigger them. Check the slicer preview layer by layer to see what it objects to.
How large a file can it handle?
It depends on your device rather than on a limit here. A 200,000-triangle model takes a second or two on an ordinary computer. Files with several million triangles work on a desktop with enough memory but take longer.