Skip to content
Creative3DP Tools

QR code stencil maker

A stencil that stays in one piece and still scans. 3D print it, or cut it on a laser or vinyl cutter.

Top view, to scale
Drag to rotate, scroll to zoom.

This code

Scan check
-
Size
-
Grid
-
Smallest square
-
Filament (PLA, solid)
-
Mesh check
-

Download

What the code opens

Presets:

Square style

Plate, frame and key ring

A blank border around the code, counted in its own squares. Phones want at least 2.

Text above and below

Long lines shrink to the width of the code.

Why ordinary QR codes make bad stencils

A QR code is a grid of dark and light squares, and the light squares are often surrounded on every side by dark ones. Cut a normal code out of a sheet and those light squares fall out, along with the middles of the three large corner squares. What is left will not hold paint back and will not scan.

This tool cuts every dark square as its own hole, with a thin wall of plastic around each one, and holds the middle of each corner square with four small bridges set to the side, away from the lines a phone reads through the middle. The scan check decodes that exact shape before you download it.

Size and paint for each job

WhereCode widthError correctionPaint with
Box, crate or toolbox60 to 90 mmLow or MediumSpray or sponge
Wall, door or shop window120 to 200 mmMediumSponge, two thin coats
Pavement, floor or event sign200 mmHighSpray chalk or line paint
Fabric, tote bag or T-shirt60 to 100 mmMediumFabric paint, dabbed
Cake or latte topping50 to 80 mmLowCocoa or icing sugar, sieved

How to make and use a QR code stencil

  1. Enter the link or other content. Shorter content makes a smaller grid with bigger, easier holes.
  2. Set the code width from the table above and check that "Smallest square" is 2 mm or more.
  3. Download the STL to 3D print it at 1 to 1.2 mm thick, or the SVG to cut it from stencil film or card.
  4. Tape it flat and dab paint straight down, or spray two light coats from 25 to 30 cm away.
  5. Lift it straight up while the paint is wet, and wipe the back before the next use.

For a code that is printed rather than painted, such as a WiFi sign, keychain or coaster, use the main QR code to STL generator with the raised or two-colour style. For lettering stencils, the text to STL generator has stencil fonts.

Frequently asked questions

How does a QR code stencil stay in one piece?

In a stencil the dark squares are holes. Where two dark squares touch, a hole would join them and the plastic between other squares could fall out. This tool cuts every square as its own hole with a thin wall around it, and gives the middle of each of the three large corner squares four small bridges. The download is one solid piece.

Will a painted stencil QR code still scan?

Yes. The thin walls between squares leave fine light lines in the paint, and phones read straight through them. The scan check beside the preview decodes the exact stencil shape, bridges included, before you download it. Use a dark paint on a light surface, or a light paint on a dark one.

What size should a QR code stencil be?

For a short link, 60 mm is the smallest that is easy to paint cleanly, because each hole is then over 2 mm. Walls and signs read from a distance want 120 to 200 mm. Phones scan from roughly ten times the code width, so a 150 mm code works from about 1.5 m away.

Can I cut the stencil on a Cricut, laser or vinyl cutter?

Yes. Download the SVG. It is drawn in millimetres at the size you set, with each square as its own shape, ready to import into any cutting software. For a reusable stencil, cut it from 0.25 to 0.5 mm stencil film or thin card.

How thick should a 3D printed stencil be?

Between 1 and 1.2 mm. Thinner sheets curl and let paint creep under the edges. Thicker sheets cast a shadow that blurs the squares when you spray at an angle. Print it flat with no supports.

How do I stop paint bleeding under the stencil?

Tape the stencil flat, use as little paint as possible, and dab straight down with a sponge or stencil brush rather than wiping across. With spray paint, hold the can 25 to 30 cm away and give two light coats. Lift the stencil straight up while the paint is still wet.

"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.